| CELLINE WLL |
| GSM FIXED TELEPHONY WIRELESS GATEWAY |
| |
| The CelLine WLL can provide a phone line in places not reached by landlines, if there is an adequate signal for mobile phones. |
| The removable GSM stub antenna can be replaced with an external cabled antenna to improve reception. |
| Using the cellular network, the CelLine WLL will allow you to make and receive calls from normal telephony equipment; telephone, fax, modem, using the Analog RJ11 port, without difference from normal communications over fixed land line. |
| Ideal for applications such as: |
| • Rural Telephony |
| • Mobile/Temporary Offices |
| • Landed Telephony Lines |
| • Back Up |
| The CelLine WLL works with primary power from 230Vac, 50/60Hz, and has a internal battery which becomes operational in case of power cuts, 2.5 hours talk or 13 hours in standby mode. |
| |
| Features: |
| • AU port for Voice, Data, SMS, FAX and Modem (V90) |
| • Local programming by the phone (DTMF tones) or through the USB port and SW application |
| • Remote programming through GSM data call by a SW application 2.0 USB port, type B |
| • SIM-CARD folding holder, 3V type; PIN code entry through DTMF tones |
| • Status LEDs |
| • Call hold, call wait, etc: GSM services handling via DTMF tones from the connected (BCA) phone |
| • Calling Line Identification Presentation (CLIP) over the AU port |
| • Teletaxe: Reverse Polarity and 12/16KHz pulses generation over the AU port |
| |
| GSM Technical Features: |
| • GSM Dual Band - 50O female SMA antenna connector |
| • RF POWER: class 4 (2W) for EGSM900; class 1 (1W) for GSM1800 |
| • Voice and emergency calls: TCH/FS |
| • Rate: Half Rate (HR), Full Rate (FR), Enhanced Full Rate (EFR) |
| • SMS: MT, MO, CB, PDU - SMS package: 140 byte (8 bit/char) - PDU format; 160 byte (7 bit/char) - Text format – According to recommendations: ETSI ES 201 912 |
| • FAX: Automatic group 3 (class 1,2) - Compliant to ITU-T T.4 and T.30 |
| • DATA (9.600 bps): GSM class 8 (max 21.4kbps uplink, max 85.6 kbps downlink), full PBCCH support, MS class B, coding scheme CS1,2,3,4, CSD up to 14.4kpbs, USSD, not transparent mode, V.110. |
| |
| AU Port Technical Features: |
| • Interface: RJ-11 4/6 connector + 2 poles terminal block |
| • Call mode: originated call (MOC), terminated call (MTC) |
| • Input dialling: pulse or DTMF |
| • ETSI EG 201 185 compliant |
| • Call current level (ring): 35Vrms ± 10% + 38Voffset |
| • Call current frequency: 25Hz ± 5% |
| • Call current modulation: 1.0s emission; 4.0s silence |
| • Local tone frequency: 425Hz ± 1% |
| • Local tone modulation accuracy (emission/silence): ± 1% |
| • Central tone modulation (request to dial): programmable |
| • Engaged and congestion tone modulation: programmable |
| • Loop current: =26mA with 0O of line resistance |
| • Characteristic PBX impedance: 750O // 150nF + 270O |
| • Maximum telephone line length: 500m |
| |
| Physical Characteristics: |
| • Dimensions: 220x170x50mm |
| • Weight: 1.4kg (internal battery included) |
| • Operating temperature: -20oC to +55oC (0-95% not condensing humidity) |
| • Storage temperature: -40oC to +85oC (0-95% not condensing humidity) |
| |
| Applicable Standards: |
| • EN 60950 (Health and Safety) |
| • EN 301 489-1/-7 (EMC) |
| • EN 301 511, EN 300 607-1 (Radio) |
| |
| | |
